Super-micro-computer 5014C-MF Instrukcja Użytkownika Strona 95
- Strona / 112
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Appendix C: Software Installation
C-1
Appendix C
Software Installation
If you do not wish to confi gure SATA RAID, proceed directly to Section C-3.
After all the hardware has been installed, you must fi rst confi gure Intel's ICH6R
SATA RAID before you install the Operating System and other software drivers.
The necessary drivers and user's guides are all included on the Supermicro CDs
that came packaged with the system.
C-1 Confi guring Intel's ICH6R SATA RAID Function
To confi gure SATA RAID functions, you must fi rst confi gure the desired RAID
level with the ICH6R SATA RAID Utility program before you install the operating
system and other software drivers. The necessary drivers are all included on the
Supermicro CDs that came packaged with your system.
Note: the current ICH6R SATA RAID Utility version can only support Windows
XP/2000/2003 and Linux/SuSE Operating Systems.
Serial ATA (SATA)
Serial ATA (SATA) is a physical storage interface that uses a single cable with a
minimum of four wires to create a point-to-point connection between devices. It
is a serial link that supports SATA transfer rates of up to 150MBps. Because the
serial cables used in SATA are thinner than the traditional cables used in Paral-
lel ATA (PATA), SATA systems have better airfl ow and can be installed in smaller
chassis than PATA. In addition, the cables used in PATA can only extend to 40
cm, while SATA cables can extend up to one meter. Overall, SATA provides better
functionality than PATA.
Intel's ICH6R Serial RAID
Located in the South Bridge of the E7221 Copper River Chipset, the I/O Controller
Hub (ICH6R) provides the I/O subsystem with access to the rest of the system.
It supports a one-channel Ultra ATA/100 Bus Master IDE controller (PATA) and a
Serial ATA (SATA) Host Controller, which supports up to four Serial ATA ports and
up to two sets of RAID drives. RAID 0 (Striping), RAID 1 (Mirroring) and RAID
10 (Striping+Mirroring) are supported. The ICH6R supports both PATA and SATA
device confi gurations.
ATA Operating Modes
You can select from the following two modes: Legacy mode and Native mode.
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Table of Contents 6
- Chapter 4: System Safety 7
- Chapter 7: BIOS 8
- Appendices: 9
- Introduction 11
- Chapter 1 11
- 1-2 Motherboard Features 12
- Other Features 13
- System Block Diagram 14
- 1-3 Server Chassis Features 15
- Cooling System 16
- 1-4 Contacting Supermicro 17
- Chapter 2 19
- Server Installation 19
- Warnings and Precautions! 20
- Rack Mounting Considerations 21
- Basic Installation Procedure 22
- Installing the Chassis Rails 23
- Installing the Rack Rails 24
- Chapter 3 31
- System Interface 31
- 3-3 Control Panel LEDs 32
- Chapter 3: System Interface 33
- Chapter 4 35
- System Safety 35
- 4-3 ESD Precautions 37
- 4-4 Operating Precautions 38
- Chapter 5 39
- Advanced Motherboard Setup 39
- 5-2 Motherboard Installation 40
- 5-3 Connecting Cables 41
- 5-4 I/O Ports 42
- 5-5 Installing the Processor 43
- Heatsink Installation 45
- Heatsink Removal 45
- 5-6 Installing Memory 46
- 5-7 Adding PCI Cards 47
- 5-8 Motherboard Details 48
- P8SCT Quick Reference 49
- 5-9 Connector 50
- Defi nitions 50
- Overheat LED (OH) 51
- NIC2 (JLAN2) LED 51
- IDE/SATA LED 51
- NIC1 (JLAN1) LED 51
- Wake-On-LAN 53
- Chassis Intrusion 53
- Universal Serial Bus (USB) 53
- JLAN1/2 (Ethernet Ports) 53
- 5-10 Jumper Settings 55
- JLAN1/JLAN2 Enable/ 57
- Disable 57
- Watch Dog Enable/Disable 57
- SMBus to PCI 57
- 5-11 Onboard Indicators 58
- Parallel Port Connector 59
- Floppy Connector 60
- IDE Connector 61
- Chapter 6 63
- Advanced Chassis Setup 63
- 6-2 Control Panel 64
- 6-3 System Fan 65
- Serial ATA Drive Installation 66
- 6-5 Power Supply 68
- Chapter 7 69
- 7-2 Running Setup 70
- 7-3 Main BIOS Setup 70
- 7-4 Advanced BIOS Setup 73
- PnP/PCI Confi guration 77
- 7-4.5 Hardware Monitors 79
- 7-4.7 DMI Event Log 81
- 7-4.8 Console Redirection 82
- 7-5 Security 83
- 7-6 Boot 84
- 7-7 Exit 85
- Appendix A 87
- BIOS POST Messages 87
- Beeps Error Messages 87
- Appendix B: 89
- BIOS POST Codes 89
- Appendix B: BIOS POST Codes 91
- Appendix C 95
- Software Installation 95
- SATA Operating Modes 96
- Creating New A SATA RAID: 98
- Initializing Disk Drives 102
- Creating Hot Spare Drives 103
- Installing Other Drivers 106
- Supero Doctor III 107
- Appendix D 109
- 109
- System Specifi cations 109
Powiązane produkty i podręczniki dla Sprzęt komputerowy Super-micro-computer 5014C-MF
(103 strony)Philips AVENT Mikrowellen-Dampfsterilisator manuels
Manuels d'utilisation et guides de l'utilisateur pour Produits pour enfants Philips AVENT Mikrowellen-Dampfsterilisator.
Nous fournissons des manuels en pdf 1 Philips AVENT Mikrowellen-Dampfsterilisator à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji